| A light weight purpose built winch on, roll off trailer is supplied. It is fitted with 13 Magnesium alloy wheels and tyres. Electric Brakes. The chassis is pre galvanized steel tubing. A mechanical 5:1 winch is fitted. |
| |
The deck of this Hovercraft is manufactured from fiberglass core sandwich resin infusion technology. Using a blown rigid PVC foam core, this provides a high tensile strength and low weight. Port and Starboard grab handle on the outer deck section.
|
| |
The Hulls is molded fibreglass with a gelcoat finish. Resin infusion system is used to produce the components.
This means that the reinforcements and the core materials are place in the mould dry and put under vacuum and the resin is drawn into the mould. This technique guarantees a quality part with a high glass to resin ratio. Light weight and high strength parts are produced using this system. This also provides an extremely high impact protection for the hull should it strike a solid object protruding from the water. There is 3/4 a cubic metre of polyurethane foam integrated within the hull structure to provide positive buoyancy.
This means that if the cockpit of the vessel was to be completely flooded the Hovercraft will remain a float and upright with a full payload on board. |
| |
| The cockpit of the craft is also gelcoat-finished fibreglass and nonskid finish molded in to the floor. In the front sidewalls of the cockpit each side of the pilot is two lockable waterproof glove compartments that are used to house VHF radio etc. Two grab handles are installed on each side of the cockpit wall. |
| |
| The duct is manufactured from Kevlar/fibreglass and is 1160 mm internal diameter. This fan provides lift as well as thrust and is designated as an integrated system. It is fitted with four steering rudders and one elevator. These provide steering and longitudinal control. |
| |
| Camouflage colour scheme to be advised. |
| |
| Tachometer, volt meter, water temperature, oil pressure
Hour meter, CHT & EGT, fuel gauge, Key Ignition, Lanyard Switch. Loud Hailer 100W amp, Siren.
|
| |
| Supply 2 x Communications Head set with 14 Channels. Supply 4 x hearing protection devices. |
| |
6 headlights, navigation light as per USL code. White light on Duct and White light on front of Hovercraft flashing type. Flashing Orange light in the top of the fan duct, Two portable Spotlights 400,000 cp. Two Halogen lights mounted on the front of the hovercraft, adjustable.
Emergency red/blue light fitted to the craft also.
|
| |
| 13 spare skirt segment ( 10 side and front, 3 Rear Skirts) 100 cable ties, Flares. |
| |
| Fire extinguisher 1 kgs Dry Powder, 5 Life jackets, First aid kit, Flashlight, 20 metres rope, Sea Anchor. 5 Safety Helmets, 2 Spot Lights, 4 Safety Floats, 4 Paddles, one electric Bilge pump V750 (750 gl/h) |
| |
| Two reverse buckets electric operation with warning buzzer and light should an error occur. Reset function fitted. These enable the craft to move in reverse. |
| |
| The steering controls on this craft are very simple and easy to operate. The throttle control is hand operated and the steering and elevator controls are all in one. Simply moving the steering left and right to steer the craft, A trim switch is fitted to the steering to electronically adjust the longitudinal stability of the craft. |
| |
| The seating is down the centre of the craft. The seat is contoured to each passenger. Beneath the seat is a large watertight storage compartment for safety equipments. |
| |
| The Skirt system is simple and easy to maintain. This craft is fitted with 69 segments. Each segment can be easily replaced if damaged. The skirt material has been developed and tested over 8 years and has been found to provide the optimum in flexibility and the lowest wear coefficient. |
| |
| The operating cost of this craft including fuel and maintenance costs is US$20.00 per hour. This is provided the craft is properly serviced and maintained. |
| |
| This craft can be put into Victorian survey at an extra cost of US$1000.00 |
| |
| The hull structure of the Hovercraft has warranty for a period of 5 years. The engine comes with manufacturer’s warranty of 12 months. |
| |
| Production lead time for the Hovercraft is 60 days from receipt of confirmed order and deposit. |
| |
| Mariah will provide 5 days of onsite training in the operation and maintenance of the Hovercraft. |
Additional Equipment: |
100W PA System
|
Waterproof Siren / Speaker
|
Portable Spotlights
|
V750 Bilge Pump
|
Head Set Communications
|
Specifications: |
4.8 meters |
2.5 meters
|
| 1.5 meters |
356 kilograms / Dry no accessories |
600 kilograms / 6 persons |
Inline, Contoured seat for passengers |
750 kilograms |
280mm |
150 kgs |
90 kph plus |
40-80 kph |
25 Litres / Optional extra 38 litre tank available |
2 Hours, 4 Hours with long range fuel tank fitted |
Yamaha 1000 cc Water-cooled 4 cylinder 4-stroke Yamaha, twin cam, 5 valves per cylinder, dry sump engine, Electronic Fuel Injection |
Electric Start |
12 Volt 520 CCH, Optional 2nd battery available |
100 Hp / 74 Kws |
Multi Wing 6/6 7XL Fan, Polyamide Glass Fill Blades |
Less than 28 knot wind speed |
1.5 to 2 metre seas |
|
$ POA |
For further information please contact us using out Contacts sections, click here to be taken there now.
|
